How to easily change a toilet in just one day without needing to call a plumber?

IN SHORT |
🛠️ Preparation of the necessary tools for replacing the toilet |
🔧 List of essential tools and materials |
🚽 Changing a toilet in one day without a plumber: key steps |
⚠️ Precautions to take when changing a toilet yourself |
🔩 Dismantle the old toilet and install the new one |
✅ Check for tightness and leaks after replacement |
Before you start replacing your toilet, make sure you gather all the necessary tools such as screwdriver, adjustable wrench, spirit level, Teflon tape, protective gloves, etc. Prepare the installation area by turning off the water, emptying the tank and removing the old toilet.
To easily change a toilet in just one day without calling a plumber, gather the necessary tools and prepare the workspace by turning off the water supply and cleaning the area. Unscrew the old bolts, remove the old toilet, clean the area, install the new toilet with a gasket, connect the water and check for leaks.
By following the carefully prepared steps for changing a toilet, you can easily install your new toilet in one day, without the help of a plumber. Be sure to check for tightness and leaks to ensure the proper functioning of your new installation.
🔧 | Buy a new toilet and the necessary tools. |
🚽 | Empty and dismantle the old toilet. |
Clean the installation area. | |
🔩 | Install the new toilet following the manufacturer’s instructions. |
🚰 | Reconnect the water supply and test the new equipment. |
🔧 How to change a toilet easily in one day?
- 1. Preparation : Make sure you have the right tools and the new toilet ready to install.
- 2. Removal of the old toilet: Close the water supply, empty the tank and dismantle the old toilet following the instructions.
- 3. Installation of the new toilet: Attach the bowl and the tank, connect the water supplies and close the fasteners.
- 4. Final test: Turn on the water supply, flush the toilet to check that everything is working properly.
- 5. Cleaning : Clean the area around the new toilet and enjoy your new equipment!
Preparing the necessary tools
Before you begin replacing your toilet, make sure you gather all the necessary tools. This will allow you to work efficiently and not waste time searching for additional items during the process.
here is a list of tools and materials what you will need:
- A slotted screwdriver and a Phillips screwdriver
- An adjustable wrench or set of open-end wrenches
- A hacksaw or handsaw to cut pipes if necessary
- A spirit level to check the balance of the toilet
- Teflon tape to ensure the tightness of the connections
- Protective gloves to prevent injuries
- A bucket and a sponge to clean residual water
- A spatula to remove old putty or glue residue
- A new toilet with all the accessories such as the tank, the bowl, and the fixings
Check that all fittings and the fixing accessories are included with your new toilet. It is important to read the instructions provided by the manufacturer carefully to ensure that you have not forgotten anything.
Once the tools And materials gathered, it is time to prepare the area where the new toilet will be installed. Remember to turn off the water at the shut-off valve and empty the existing toilet tank by flushing the toilet several times. Then remove the old toilet by unscrewing the bolts and disconnecting the water inlet pipe.
Clean the location thoroughly to remove any traces of putty or glue and prepare a clean, flat surface for the installation of the new toilet.
List of tools to provide
To easily change a toilet in a single day without calling a plumber, it is important to be well prepared. The first step is to gather all the tools needed for the job. Proper preparation saves time and avoids unnecessary interruptions.
List of tools to provide:
- Adjustable wrench
- Screwdriver (flat and cross)
- Metal saw
- Drill with suitable drill bits
- Seals
- Sanitary silicone
- Protective gloves
- Container to collect water
- Sponge and cloth
Once you have gathered the tools, it is also crucial to make sure you have the necessary supplies. This includes a new toilet, connection pipes, and possibly dowels and screws suitable for your installation.
Wear protective gloves to avoid any risk of injury and use a cloth to wipe the surfaces as you go. THE container for collecting water is essential to avoid water overflows when dismantling the old toilet.
Then proceed with the installation following the instructions provided with your new toilet. Be sure to check the seals carefully to avoid leaks and use sanitary silicone to seal the contours of the toilet base after installation.
By following these steps and taking the time to properly prepare your equipment, you will be able to change your toilet with complete peace of mind and without the help of a plumber.
Precautions to take
Change one WC is a task that you can complete yourself in a single day, without needing to call a plumber. Follow these instructions to make your plumbing project a success.
Before you begin, prepare all the necessary tools. You will need:
- An adjustable wrench
- A screwdriver
- Bucket
- A cloth
- A putty knife
- Teflon tape
- A new toilet bowl and cistern
- A wax seal
To avoid any damage, take a few simple precautions. Turn off the water supply to the toilet and flush the toilet to empty the tank. Place a bucket under the water tap to collect any residual water and use a cloth to wipe up any drips.
Next, unscrew the nuts that hold the toilet in place using the adjustable wrench. Carefully lift the old toilet and place it aside. Remove the used wax seal with the putty knife and clean the area.
Apply a new wax seal to the base of the new toilet. Carefully position the new bowl over the gasket, aligning the bolts with the holes in the base. Tighten the nuts by hand at first, then use the wrench for final tightening without applying too much force.
Connect the tank to the bowl following the manufacturer’s instructions. Use Teflon tape on pipe threads to prevent leaks. Connect the water supply hose and turn on the water supply. Check for leaks.
Flush the toilet to make sure everything is working properly, and voilà, you’ve easily changed a toilet in just one day.
Preliminary step: turn off the water supply
To change a WC quickly and without the help of a plumber, it is crucial to prepare properly by gathering all the necessary tools. You will need an adjustable wrench, screwdriver, hacksaw, water pump pliers, spirit level, silicone gasket and new mounting bolts.
Before starting to replace your toilet, cut thewater inlet. To do this, locate the stopcock usually located near the floor next to the toilet. Turn this faucet clockwise until it is completely closed. To ensure the water is turned off, flush the toilet to empty the tank.
Once the water supply is turned off, use the screwdriver to unscrew the fixing bolts located at the base of the toilet. Using water pump pliers, disconnect the water supply hose. Then lift the toilet from its location. This step sometimes requires two people due to the weight of the device.
Thoroughly clean the area where the toilet was installed, removing any remaining silicone or old seal. If necessary, use a hacksaw to cut out old mounting bolts if they are corroded.
Position the new toilet making sure it is aligned with the drain pipe. Use the spirit level to check that it is level. Attach the new mounting bolts and tighten them with the adjustable wrench. Finally, reconnect the water supply hose.
Apply a silicone sealant around the base of the toilet to ensure a good seal. Once the silicone has dried, open the shut-off valve to restore the water supply and test the installation by flushing the toilet.
It is recommended to check the mounting bolts and sealing regularly during the first few days to ensure everything is secure.
Changing the toilet

For change a toilet easily in a single day without calling a plumber, here are the steps to follow:
1. Preparing the space
First of all, turn off the water supply. Empty the tank by flushing the toilet and blot up the excess water. Unscrew the shut-off valve to prevent leaks. Finally, remove the tank cover.
2. Removal of the old toilet
Unscrew the bolts that secure the toilet to the floor. Carefully lift the bowl and reservoir to remove them. Be careful not to damage the wastewater evacuation pipe.
3. Cleaning the area
Thoroughly clean and dry the floor where the old toilet was placed. Be sure to remove residue from the old installation to ensure a good seal of the new toilet.
4. Installation of the new toilet
Place a new wax seal on the toilet drain outlet. Position the toilet on the joint so that it is stable. Screw the bolts into the floor to secure the bowl.
Next, install the tank by connecting it to the bowl. Be sure to correctly position the seals between the tank and the bowl to avoid leaks. Tighten the screws gently so as not to crack the ceramic.
5. Connection to the water supply
Connect the water supply hose to the tank. Slowly open the shut-off valve to fill the tank and check for leaks.
- Check the joints and tighten if necessary.
- Make sure the toilet flushes properly.
By following these steps, you can perform the replacing your toilet easily and quickly, without having to call on a professional.
Dismantle the old toilet
To replace your old one WC, make sure you have all the necessary tools and a new toilet bowl on hand. Here’s how to do it step by step.
Dismantle the old toilet:
Before you begin, turn off the water supply. Empty the bowl and tank by flushing the toilet several times until no more water remains.
Use a wrench to unscrew the bolts that hold the tank to the bowl. Lift and remove the tank. Next, unscrew the bolts securing the bowl to the floor. These bolts may be covered with plastic caps that will need to be removed.
Once the bolts are removed, gently rock the bowl to break the seal. Lift the bowl and set it aside. Block the drain pipe with a cloth to avoid bad odors.
Install the new toilet:
Carefully clean the old gasket and silicone residue with a spatula and nail polish remover, then place a new wax gasket on the drain flange.
Install the new bowl by aligning the holes with those in the flange. Press firmly to ensure a good seal. Screw in the mounting bolts and cover them with the plastic caps.
Install the tank onto the bowl by securing the bolts securely. Connect the water supply hose to the tank. Gradually open the water supply and check that there are no leaks.
Adjustments and checks:
Fill the tank and test the flush to make sure everything is working properly. Adjust the bolts and float as necessary to avoid leaks or filling problems.
Once everything is properly adjusted and checked, you can put your tools away and enjoy your new toilet.
Install the new toilet
Change one WC may seem complicated, but with the good instructions, it is entirely possible to do it yourself in just one day. Here’s how to do it.
Before you begin, make sure you have all tools required :
- Adjustable wrench
- Screwdriver
- Bucket
- Sponge
- Spirit level
- Seal
And follow these steps:
1. Prepare the workspace
Turn off the water supply to the toilet by closing the shut-off valve. Flush the toilet to empty the tank and use a sponge to remove any remaining water.
2. Dismantle the old toilet
Unscrew the bolts holding the toilet to the floor and remove the nuts securing the tank. Lift the toilet carefully and place it on a blanket to avoid dirtying the floor. Clean grout and caulk residue from the floor and ledge.
3. Install the new toilet
Position the new seal over the floor drain. Line up the new toilet’s mounting bolts with the holes in the floor and lower it into place. Tighten the bolts with an adjustable wrench, but do not overtighten to avoid breaking the ceramic.
4. Secure the tank
Place the tank on the bowl and tighten the bolts using washers to avoid cracking the porcelain. Make sure the tank is aligned and level with the help of a spirit level.
5. Connect water
Reconnect the water supply hose to the tank. Open the shut-off valve and allow the tank to fill. Check for leaks around fittings and joints.
6. Testing and finishing
Once the tank is full, flush the toilet to make sure everything is working properly. Check one last time to make sure there are no leaks around the toilet.
This method allows you to replace a toilet efficiently by following simple steps and detailed. You will avoid the costs of a plumber while acquiring new DIY skills.
Check for tightness and leaks
Changing a toilet without calling a plumber can be easier than you think. Here’s how you can do it in a day.
Prepare your equipment:
- New toilet
- Adjustable wrench
- Screwdriver
- Mesureing tape
- Silicone gasket
- Hacksaw (if necessary to fit pipes)
Turn off the water at the shut-off valve located near the old toilet. Next, flush the toilet to empty the tank and disconnect the water line. Use a sponge to remove any remaining water in the tank and bowl.
Loosen the bolts securing the old toilet to the floor with the adjustable wrench. Carefully lift the old bowl and tank and set them aside. If the wax seal is damaged, scrape it with a putty knife.
Position the new wax seal on the floor flange. Position the new toilet by aligning the mounting holes with the bolts on the floor. Press firmly to seal the wax seal. Secure the bolts with the adjustable wrench.
Install the tank following the manufacturer’s instructions. Connect the water line and open the shut-off valve to let water fill the tank. Check the flow of water by flushing the toilet several times.
Check for tightness and leaks:
- Make sure all connections are tight.
- Apply silicone seal around the base of the toilet to prevent leaks.
- Monitor for a few hours to make sure there is no moisture or water leaking.